Altronix EFLOW102NA8 8 Fused Relay Outputs Access Power Controller with Power Supply/Charger, BC400 Enclosure
Product Highlights
The eFlow102NA8 distributes and switches power to access control systems and accessories. It converts a 120VAC 60Hz input into eight (8) independently controlled 12VDC fuse protected outputs with a total of 10 amp continuos supply current. These power outputs can be converted to dry form "C" contacts. Outputs are activated by an open collector sink or normally open (NO) dry trigger input from an Access Control System, Card Reader, Keypad, Push Button, PIR, etc. Unit will route power to a variety of access control hardware devices including: Mag Locks, Electric Strikes, Magnetic Door Holders, etc. Outputs will operate in both Fail-Safe and/or Fail-Secure modes. The FACP Interface enables Emergency Egress, Alarm Monitoring, or may be used to trigger other auxiliary devices. The fire alarm disconnect feature is individually selectable for any or all of the eight (8) outputs.
Features
- Input 120VAC 60Hz, 3.5 amp
- 12VDC outputs @ 10 amp supply current
- Eight (8) independently trigger controlled outputs
- AC fail supervision (form "C" contacts)
- Battery fail & presence supervision (form "C" contacts)
- Low power shutdown. Shuts down DC output terminals if battery voltage drops below 71-73% (depending on the power supply)
- Prevents deep battery discharge
- AC input and DC output LED indicators
- Built-in charger for sealed lead acid or gel type batteries
- Power Supply Board maximum charge current 1.54 amp
- Automatic switch over to stand-by battery when AC fails. Transfer to stand-by battery power is instantaneous with no interruption
- Zero voltage drop when unit switches over to battery backup (AC failure condition)
Downloads
Condition | New |
---|---|
Brand | Altronix |
Output Type | DC |
Fire Alarm Interface | Yes |
Certifications | CE, CSFM, cUL, UL |
Power Options | 10 amp @ 12VDC |
Output Protection | Fuse |
Number of Outputs | 8 |
Input Voltage | 120VAC |
Battery Charging | Yes |
The eFlow102NA8 distributes and switches power to access control systems and accessories. It converts a 120VAC 60Hz input into eight (8) independently controlled 12VDC fuse protected outputs with a total of 10 amp continuos supply current. These power outputs can be converted to dry form "C" contacts. Outputs are activated by an open collector sink or normally open (NO) dry trigger input from an Access Control System, Card Reader, Keypad, Push Button, PIR, etc. Unit will route power to a variety of access control hardware devices including: Mag Locks, Electric Strikes, Magnetic Door Holders, etc. Outputs will operate in both Fail-Safe and/or Fail-Secure modes. The FACP Interface enables Emergency Egress, Alarm Monitoring, or may be used to trigger other auxiliary devices. The fire alarm disconnect feature is individually selectable for any or all of the eight (8) outputs.
Features
- Input 120VAC 60Hz, 3.5 amp
- 12VDC outputs @ 10 amp supply current
- Eight (8) independently trigger controlled outputs
- AC fail supervision (form "C" contacts)
- Battery fail & presence supervision (form "C" contacts)
- Low power shutdown. Shuts down DC output terminals if battery voltage drops below 71-73% (depending on the power supply)
- Prevents deep battery discharge
- AC input and DC output LED indicators
- Built-in charger for sealed lead acid or gel type batteries
- Power Supply Board maximum charge current 1.54 amp
- Automatic switch over to stand-by battery when AC fails. Transfer to stand-by battery power is instantaneous with no interruption
- Zero voltage drop when unit switches over to battery backup (AC failure condition)
Downloads
Condition | New |
---|---|
Brand | Altronix |
Output Type | DC |
Fire Alarm Interface | Yes |
Certifications | CE, CSFM, cUL, UL |
Power Options | 10 amp @ 12VDC |
Output Protection | Fuse |
Number of Outputs | 8 |
Input Voltage | 120VAC |
Battery Charging | Yes |