Muxlab 500752-RX HDMI Over IP Decoder With PoE
Product Highlights
The HDMI over IP extender allows HDMI equipment to be connected up to 330feet (100m) @ 1080p via one (1) Cat5e/6 unshielded twisted pair cable in a point-to-point configuration. Point-to-multipoint and multipoint-to-multipoint is possible by connecting several Transmitters and Receivers to the same Ethernet network. The Transmitter (500752-TX) and Receiver (500752-RX) also support PoE (PD) if used with a PoE (PSE) Ethernet Switch. The HDMI over IP extender kit comes with one (1) Transmitter and one (1) Receiver ideal for starting to set up your HDMI over IP network. The IR Emitter and IR Sensor, if required, may be purchased separately for remote control applications. For the point-to-multipoint and multipoint-to-multipoint configuration the Ethernet switch must have Gigabit ports, DHCP Server capability and IGMP communications protocol. MuxLab recommends using the Cisco SG300 Series Managed Switches. The MuxLab Pro Digital Network Controller (500811) is available to simplify the configuration and utilization of the MuxLab IP based products via an Ethernet web interface, and supports third party management via smartphone and tablet.
Features
- HDMI 1.3
- HDMI over IP extender Supports up to 1080p resolutions
- Motion JPEG compression with Very low latency
- Supports 100’s of Transmitters and Receivers, depending on network bandwidth
- Supports point-to-point, point-to-multipoint, and multipoint-to-multipoint applications
- Transmission up to 330ft (100m) over Cat5e/6
- Up to 390ft (120m) between the TX and RX? when no LAN switch is used
- HDMI over IP extender Supports IR transmission for remote control
- PoE powered
- Control via any web device (mobile, tablet) with use of model 500811 (Pro Digital Network Controller)
| Condition | New |
|---|---|
| Brand | MuxLab |
| NDAA Compliance | No |
| Product Type | Passive Transmitter |
| Channels | 1 |
| Connection Type | 3.5mm Jack, HDMI, RJ-45 |
| Form | Stand - Alone |
The HDMI over IP extender allows HDMI equipment to be connected up to 330feet (100m) @ 1080p via one (1) Cat5e/6 unshielded twisted pair cable in a point-to-point configuration. Point-to-multipoint and multipoint-to-multipoint is possible by connecting several Transmitters and Receivers to the same Ethernet network. The Transmitter (500752-TX) and Receiver (500752-RX) also support PoE (PD) if used with a PoE (PSE) Ethernet Switch. The HDMI over IP extender kit comes with one (1) Transmitter and one (1) Receiver ideal for starting to set up your HDMI over IP network. The IR Emitter and IR Sensor, if required, may be purchased separately for remote control applications. For the point-to-multipoint and multipoint-to-multipoint configuration the Ethernet switch must have Gigabit ports, DHCP Server capability and IGMP communications protocol. MuxLab recommends using the Cisco SG300 Series Managed Switches. The MuxLab Pro Digital Network Controller (500811) is available to simplify the configuration and utilization of the MuxLab IP based products via an Ethernet web interface, and supports third party management via smartphone and tablet.
Features
- HDMI 1.3
- HDMI over IP extender Supports up to 1080p resolutions
- Motion JPEG compression with Very low latency
- Supports 100’s of Transmitters and Receivers, depending on network bandwidth
- Supports point-to-point, point-to-multipoint, and multipoint-to-multipoint applications
- Transmission up to 330ft (100m) over Cat5e/6
- Up to 390ft (120m) between the TX and RX? when no LAN switch is used
- HDMI over IP extender Supports IR transmission for remote control
- PoE powered
- Control via any web device (mobile, tablet) with use of model 500811 (Pro Digital Network Controller)
| Condition | New |
|---|---|
| Brand | MuxLab |
| NDAA Compliance | No |
| Product Type | Passive Transmitter |
| Channels | 1 |
| Connection Type | 3.5mm Jack, HDMI, RJ-45 |
| Form | Stand - Alone |
Customers also viewed
Check items to add to the cart or select all
